Video: Securing Your Cylinder Head With Summit Racing and ARP

The responsibility given to whatever cylinder head fasteners you choose to clamp your head to the surface of the block is truly a matter of mechanical life or death. Those fasteners must be able to handle the extreme abuse created within each combustion chamber as the fuel mixture burns and the pressure rapidly expands underneath, with events happening thousands of times per minute.

Summit Racing gives viewers the inside scoop on the difference between ARP cylinder head fasteners, which would be better for your engine, and how to properly install your chosen fasteners. The engineers behind these fastener designs at ARP must take into account the material selection, tensile strength, torsional strength, shear resistance and cyclic fatigue of each style of fastener to guarantee reliability in even the highest horsepower engines.

Bolt Versus Stud

When you begin your search for cylinder head fasteners, you will usually find both head studs and head bolts offered for your application. But which one should you choose? In the end it all comes down to what the specific application is being used for and how much working room you have available in the engine bay.

Simply put, head studs are installed into the block prior to the cylinder head being installed. This allows for guaranteed alignment between the cylinder head, gasket, and block, while also allowing for faster service times and more accurate values when retorquing.

The drawback is that studs are generally more expensive and require enough surrounding space to allow the cylinder head to be installed from directly overhead. So components such as brake master cylinders, brake boosters, wheel tubs, and strut bars can all become potential obstacles.

Cylinder head bolts on the other hand are installed after the gasket and cylinder head have been set in place — making it slightly more difficult to keep each piece properly aligned. This allows for installation in areas that would otherwise obstruct the installation path of the cylinder head if using studs.

Material Stretch

One of the most important aspects when it comes to cylinder head fasteners is material stretch during installation, with two primary types of force being applied, but in vastly different ways depending on the type of fastener chosen. These two forces are measured as torsional force (twisting) and tensile force (pull/stretch).

When a cylinder head bolt is threaded into a block, there is of course the clamping force produced by the bolt threads as it is tightened, but there is also a force being applied to the bolt in a twisting action known as torsional force. This twisting action has been known to skew torque values.

As noted previously, studs are generally installed directly into the block finger tight prior to the head and gasket being set in place, eliminating the twisting force applied to the body itself during torquing. Instead, a nut is then used on top of the stud to apply the twisting action and clamping force across the entire body of the stud.

Typical tensile overload or stretch failure of a fastener exposed to too much preload [left], and a fastener failure due to torsional (twisting) shearing [right].

Article Sources

About the author

Kyle Kitchen

Born and raised in Southern California, Kyle has been a gearhead ever since seeing his first Mitsubishi Evo VIII in 2003. He is almost entirely self taught mechanically, and as an inexperienced enthusiast always worked on his own vehicles, regardless of the difficulty, just to learn how to do it himself. Prior to becoming a freelance writer for the company, Kyle started his automotive performance career with Power Automedia as a shop technician, where he gleaned intimate knowledge of LS platforms and drag racing builds; then later joining the editorial team as the Staff Writer for EngineLabs And Turnology. Today, Kyle is an experienced EFI calibrator; hot rod builder; and motorsports technician living in the San Jose area. Kyle is a track junkie with lots of seat time. You can usually find him racing his Mitsubishi Evo X in local time attack and road race events.
Read My Articles

Late Model LS Power in your inbox.

Build your own custom newsletter with the content you love from LSX Magazine, directly to your inbox, absolutely FREE!

Free WordPress Themes
LSX Magazine NEWSLETTER - SIGN UP FREE!

We will safeguard your e-mail and only send content you request.

LSX Magazine - The Late Model GM Magazine for Camaro

lsxmag

We'll send you the most interesting LSX Magazine articles, news, car features, and videos every week.

LSX Magazine - The Late Model GM Magazine for Camaro

LSX Magazine NEWSLETTER - SIGN UP FREE!

We will safeguard your e-mail and only send content you request.

LSX Magazine - The Late Model GM Magazine for Camaro

lsxmag

Thank you for your subscription.

Subscribe to more FREE Online Magazines!

We think you might like...


chevyhardcore
Classic Chevy Magazine
dragzine
Drag Racing
enginelabs
Engine Tech

LSX Magazine - The Late Model GM Magazine for Camaro

Thank you for your subscription.

Subscribe to more FREE Online Magazines!

We think you might like...

  • chevyhardcore Classic Chevy Magazine
  • dragzine Drag Racing
  • enginelabs Engine Tech

LSX Magazine - The Late Model GM Magazine for Camaro

lsxmag

Thank you for your subscription.

Thank you for your subscription.

LSX Magazine - The Late Model GM Magazine for Camaro

Thank you for your subscription.

Thank you for your subscription.

Loading